Fenix LD05 V2.0 EDC LED Flashlight with UV Lighting

The Fenix LD05 will be shipping August 20th!

The Fenix LD05 V2.0 is a easy to use dual lighting source penlight with warm white light and UV lighting also. The all new Fenix LD05 V2.0 uses a 90 CRI CREE XQ-E HI LED and a 365nm UV LED. Operating the Fenix LD05 is simple, the stainless steel tail switch controls all three warm white light outputs and the UV light output. A single click turns the Fenix LD05 on, and half clicks allows you to increase the outputs. The Fenix LD05 V2.0 is powered by two AAA batteries which deliver an amazing 100 Lumens of output. This light is perfect for doctors and dentists as well as helps with medical inspections in low-light areas. The powerful UV light also provide easy detection of counterfeit currency. Get your Fenix LD05 V2.0 today!

Features:

• 90 CRI CREE XQ-E HI LED with a lifespan of 50,000 hours
• 365nm/200mW UV light
• 100 Lumen Output of warm white light
• Outputs:
• High - Alkaline Battery 100 Lumens - 1 hr. 40min. / Ni-MH Battery 2 hr. 10min.
• Mid - Alkaline Battery 25 Lumens - 7 hr. 50min. / Ni-MH Battery - 6 hr. 40min.
• Low - Alkaline Battery 5 Lumens - 70 hr. / Ni-MH Battery - 36 hr.
• UV- 365nm UV lighting 200mW  - Alkaline Battery 9 hr. / Ni-MH - 7 hr.
• Stainless steel head and tail switch
• Powered by 2 AAA Batteries
• Color Temperature of 3000K
• Color Rendering Index: 90
• Soft smooth beam
• Premium HAIII hard-anodized anti-abrasive finish
• Stainless steel pocket clip
• Optimal quality optical lens
• IP68 rated - submersible 2 Meters/6.5ft. for 30 minutes

Batteries Used (Included)

• 2 - Alkaline AAA Battery (Included)
• 1 - Ni-MH Battery (Not included)
• View the AAA charger and battery bundle that is compatible with the Fenix LD05 V2.0

Size 

• Length - 135mm / 5.3 inches
• Diameter - 13.5mm / 0.53 inches
• Weight (excluding batteries) - 29.7g / 1.04 ounces

What's Included:

• 1 - Fenix LD05 V2.0
• 2 - AAA Batteries
• 1 - Spare O-ring
• 1 - User Manual
• 1 - Warranty Card
• 1 - Product Leaflet

Instruction Manual

ON/OFF ①

• Fully press the tail switch to turn on/off the light.

Output Selection ①

• With the light switched on, tap the tail switch to cycle through Low→Med→High→UV.

Battery Specifications

Warning:

• When the voltage level drops below a preset level, the flashlight is programmed to downshift to a lower brightness level until Low output is reached. To ensure normal use, the flashlight will not turn off automatically and will work till the battery runs out completely.

 Battery Replacement ②

• Unscrew the head to insert the battery with the anode side (+) towards the light head, then screw the light head back on.

Intelligent Memory Circuit

• The light memorizes the last selected brightness level. When turned on again the previously used brightness level will be recalled.

Time-limited Downshift

• The light will accumulate a lot of heat when used on High output level for extended periods. When the light has been used on High for 3 minutes, the light will automatically step down by a few lumens until 60 lumens is reached to reduce the temperature. High mode can be reselected.

Usage and Maintenance 

• Disassembling the sealed head can cause damage to the light and will void the warranty.
• Fenix recommends using excellent quality batteries. 
• Fenix strongly recommends using high-performance Ni-MH rechargeable batteries to get the most out of this light. Alkaline batteries will reduce the runtime relatively.
• If the light will not be used for an extended period, remove the battery, or the light could be damaged by electrolyte leakage or battery explosion.
• Long-term use can result in O-ring wear. To maintain a proper water seal, replace the ring with an approved spare．
• Periodic cleaning of the battery contacts improves the lamp's performance as dirty contacts may cause the lamp to flicker, shine intermittently or even fail to illuminate for the following reasons:
• A: The battery needs replacing.
• Solution: Replace battery (Ensure battery is inserted according to the manufacturer’s   specifications).
• B: The threads, PCB board contact or other contacts are dirty.
• Solution: Clean the contact points with a cotton swab soaked in rubbing alcohol.
• If the above methods don't work, please contact your authorized distributor.

Included

• LD05 V2.0, 2*AAA batteries, Spare O-ring, User manual, Warranty card, Product folding

Warning

• This flashlight is a high-intensity lighting device with UV light capable of causing eye damage to the user or others. Avoid shining the flashlight directly into anyone’s eyes.